[ Upstream commit 2501c1bb054290679baad0ff7f4f07c714251f4c ]
While modifying the driver to use the STOP interrupt, the completion of the
intermediate transfers need to wake the driver back up in order to initiate
the next transfer (restart condition). Otherwise you get never ending
interrupts and only the first transfer sent.
Fixes: 71ccea095ea1 ("i2c: riic: correctly finish transfers")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e1929dedea36781e25902118c93edd8d8f09af1 ]
The cadence I2C driver calls cdns_i2c_writereg(..) to setup a workaround
in the controller, but did so after calling i2c_add_adapter() which starts
probing devices on the bus. Change the order so that the configuration is
completely finished before using the adapter.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e0c9507bf51e1517a80ad0ac171e5402528fcef upstream.
On Apollo Lake devices the BIOS does not set up IRQ routing for the i801
SMBUS controller IRQ, so we end up with dev->irq set to IRQ_NOTCONNECTED.
Detect this and do not try to use the irq in this case silencing:
i801_smbus 0000:00:1f.1: Failed to allocate irq -2147483648: -107
BugLink: https://communities.intel.com/thread/114759
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71ccea095ea1d4efd004dab971be6d599e06fc3f ]
This fixes the condition where the controller has not fully completed its
final transfer and leaves the bus and controller in a undesirable state.
At the end of the last transmitted byte, the existing driver would just
signal for a STOP condition to be transmitted then immediately signal
completion. However, the full STOP procedure might not have fully taken
place by the time the runtime PM shuts off the peripheral clock, leaving
the bus in a suspended state.
Alternatively, the STOP condition on the bus may have completed, but when
the next transaction is requested by the upper layer, not all the
necessary register cleanup was finished from the last transfer which made
the driver return BUS BUSY when it really wasn't.
This patch now makes all transmit and receive transactions wait for the
STOP condition to fully complete before signaling a completed transaction.
With this new method, runtime PM no longer seems to be an issue.
Fixes: 310c18a414 ("i2c: riic: add driver")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fe16195f89173652cf111d7b384941b00c5aabd upstream.
AMD Family 17h uses the KERNCZ SMBus controller. While its documentation
is not publicly available, it is documented in the BIOS and Kernel
Developer’s Guide for AMD Family 15h Models 60h-6Fh Processors.
On this SMBus controller, the port select register is at PMx register
0x02, bit 4:3 (PMx00 register bit 20:19).
Without this patch, the 4 SMBus channels on AMD Family 17h chips are
mirrored and report the same chips on all channels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6ebcedbab7ca78984959386012a17b21183e1a3 upstream.
Commit b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for
block reads") broke I2C block reads. It aimed to fix normal SMBus block
read, but changed the correct behavior of I2C block read in the process.
According to Documentation/i2c/smbus-protocol, one vital difference
between normal SMBus block read and I2C block read is that there is no
byte count prefixed in the data sent on the wire:
SMBus Block Read: i2c_smbus_read_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Count] A [Data] A [Data] A ... A [Data] NA P
I2C Block Read: i2c_smbus_read_i2c_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P
Therefore the two transaction types need to be processed differently in
the driver by copying of the dma_buffer as done previously for the
I2C_SMBUS_I2C_BLOCK_DATA case.
Fixes: b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for block reads")
Signed-off-by: Pontus Andersson <epontan@gmail.com>
Tested-by: Stephen Douthit <stephend@adiengineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3ccc921b7d8fd1fcd10a00720e09823d8078666 ]
When going to suspend, the I2C registers may be lost because the power to
VDDcore is cut. Restore them when resuming.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba201c4f5ebe13d7819081756378777d8153f23e upstream.
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c159a9cb69c2cf0bf59d4e12c3a2da77e4d994 upstream.
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
count data1 data2 data3 data4
0x04 0xde 0xad 0xbe 0xef
That's what we want to return in data->block to the next level.
Instead we were actually prefixing that with desc->rxbytes:
bad
count count data1 data2 data3 data4
0x05 0x04 0xde 0xad 0xbe 0xef
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a23318feeff662c8d25d21623daebdd2e55ec221 upstream.
The commit 8503ff1665 ("i2c: designware: Avoid unnecessary resuming
during system suspend"), may suggest to the PM core to try out the so
called direct_complete path for system sleep. In this path, the PM core
treats a runtime suspended device as it's already in a proper low power
state for system sleep, which makes it skip calling the system sleep
callbacks for the device, except for the ->prepare() and the ->complete()
callbacks.
However, the PM core may unset the direct_complete flag for a parent
device, in case its child device are being system suspended before. In this
scenario, the PM core invokes the system sleep callbacks, no matter if the
device is runtime suspended or not.
Particularly in cases of an existing i2c slave device, the above path is
triggered, which breaks the assumption that the i2c device is always
runtime resumed whenever the dw_i2c_plat_suspend() is being called.
More precisely, dw_i2c_plat_suspend() calls clk_core_disable() and
clk_core_unprepare(), for an already disabled/unprepared clock, leading to
a splat in the log about clocks calls being wrongly balanced and breaking
system sleep.
To still allow the direct_complete path in cases when it's possible, but
also to keep the fix simple, let's runtime resume the i2c device in the
->suspend() callback, before continuing to put the device into low power
state.
Note, in cases when the i2c device is attached to the ACPI PM domain, this
problem doesn't occur, because ACPI's ->suspend() callback, assigned to
acpi_subsys_suspend(), already calls pm_runtime_resume() for the device.
It should also be noted that this change does not fix commit 8503ff1665
("i2c: designware: Avoid unnecessary resuming during system suspend").
Because for the non-ACPI case, the system sleep support was already broken
prior that point.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de3ec4f1d4ba6ee380478055104eb918bd50cce upstream.
The BSC data buffers to send and receive data are each of size 32 bytes
or 8 bytes 'xfersz' depending on SoC. The problem observed for all the
combined message transfer was if length of data transfer was a multiple
of 'xfersz' a repeated START was being transmitted by BSC driver. Fixed
this by appropriately setting START/STOP conditions for such transfers.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f43128c75202f29ee71aa83e6c320a911137c189 ]
Since '701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")' we
are using the SMBSLVCNT register at offset 0x8. We need to request it.
Fixes: 701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bbb27fc33d44e7b8d96369810654df4ee1837566 ]
SMBSLVCNT must be protected with the piix4_mutex_sb800 in order to avoid
multiple buses accessing to the semaphore at the same time.
Fixes: 701dc207bf55 ("i2c: piix4: Avoid race conditions with IMC")
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2474541032db65d02bf88b6a8c2f954654b443f upstream.
Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.
The BCM2835 ARM Peripherals datasheet has this to say about the flags:
TXD: is set when the FIFO has space for at least one byte of data.
RXD: is set when the FIFO contains at least one byte of data.
TXW: is set during a write transfer and the FIFO is less than full.
RXR: is set during a read transfer and the FIFO is or more full.
Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e1e4949f9dfb053122785cd73540bb1e61f768b upstream.
Refcount of of_node is increased with of_node_get() in i2c_mux_add_adapter().
It must be decreased with of_node_put() in i2c_mux_del_adapters().
Signed-off-by: Qi Hou <qi.hou@windriver.com>
Reviewed-by: Zhang Xiao <xiao.zhang@windriver.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12688dc21f71f4dcc9e2b8b5556b0c6cc8df1491 upstream.
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f638c1cb0a1112dbe0b682a42db30521646686b upstream.
smbus functions return -ve on error, 0 on success. However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater.)
The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.
Fix this by making pca954x_reg_write() return a negative error code for
all failure cases.
Fixes: 463e8f845c ("i2c: mux: pca954x: retry updating the mux selection on failure")
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 701dc207bf551d9fe6defa36e84a911e880398c3 upstream.
On AMD's SB800 and upwards, the SMBus is shared with the Integrated
Micro Controller (IMC).
The platform provides a hardware semaphore to avoid race conditions
among them. (Check page 288 of the SB800-Series Southbridges Register
Reference Guide http://support.amd.com/TechDocs/45482.pdf)
Without this patch, many access to the SMBus end with an invalid
transaction or even with the bus stalled.
Reported-by: Alexandre Desnoyers <alex@qtec.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>:
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30f939feaeee23e21391cfc7b484f012eb189c3c upstream.
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f724fb3039522486fce2e32e4c0fbe238a6ab02 upstream.
In of_i2c_register_device(), when the check for
device address validity fails we print the info.addr,
which has not been assigned properly.
Fix this by printing the actual invalid address.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: b4e2f6ac12 ("i2c: apply DT flags when probing")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0317e6c0f1.
Srinivas reported recently touchscreen and touchpad stopped working in
Haswell based machine in Linux 4.9-rc series with timeout errors from
i2c_designware:
[ 16.508013] i2c_designware INT33C3:00: controller timed out
[ 16.508302] i2c_hid i2c-MSFT0001:02: failed to change power setting.
[ 17.532016] i2c_designware INT33C3:00: controller timed out
[ 18.556022] i2c_designware INT33C3:00: controller timed out
[ 18.556315] i2c_hid i2c-ATML1000:00: failed to retrieve report from device.
I managed to reproduce similar errors on another Haswell based machine
where touchscreen initialization fails maybe in every 1/5 - 1/2 boots.
Since root cause for these errors is not clear yet and debugging is
ongoing it's better to revert this commit as we are near to release.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When loading the TX fifo to receive bytes on the I2C bus, we incorrectly
count the number of bytes:
rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR);
while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) {
if (rx_limit - dev->rx_outstanding <= 0)
break;
rx_limit--;
dev->rx_outstanding++;
}
DW_IC_RXFLR indicates how many bytes are available to be read in the
FIFO, dev->rx_fifo_depth is the FIFO size, and dev->rx_outstanding is
the number of bytes that we've requested to be read so far, but which
have not been read.
Firstly, increasing dev->rx_outstanding and decreasing rx_limit and then
comparing them results in each byte consuming "two" bytes in this
tracking, so this is obviously wrong.
Secondly, the number of bytes that _could_ be received into the FIFO at
any time is the number of bytes we have so far requested but not yet
read from the FIFO - in other words dev->rx_outstanding.
So, in order to request enough bytes to fill the RX FIFO, we need to
request dev->rx_fifo_depth - dev->rx_outstanding bytes.
Modifying the code thusly results in us reaching the maximum number of
bytes outstanding each time we queue more "receive" operations, provided
the transfer allows that to happen.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rather than reporting success for a short transfer due to interrupt
latency, report an error both to the caller, as well as to the kernel
log.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Deselect functionality can be ignored for device-trees with
"i2c-mux-idle-disconnect" entries if no platform_data is available.
By enabling the deselect functionality outside the platform_data
block the logic works as it did in previous kernels.
Fixes: 7fcac98071 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Ziyang Wu <ziywu@cisco.com>
[touched up a few minor issues /peda]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
since clk_prepare_enable() is used to get i2c->clk, we should
use clk_disable_unprepare() to release it for the error path.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We get the following build error from UM Linux after adding
an entry to drivers/iio/gyro/Kconfig that issues "select I2C_MUX":
ERROR: "devm_ioremap_resource"
[drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
ERROR: "of_address_to_resource"
[drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
It appears that the I2C mux core code depends on HAS_IOMEM
for historical reasons, while CONFIG_I2C_MUX_REG does *not*
have a direct dependency on HAS_IOMEM.
This creates a situation where a allyesconfig or allmodconfig
for UM Linux will select I2C_MUX, and will implicitly enable
I2C_MUX_REG as well, and the compilation will fail for the
register driver.
Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and
removing the dependency from I2C_MUX.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Jonathan Cameron <jic23@jic23.retrosnub.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Some drivers like i2c-gpio do not have dedicated pinctrl states. They
broke when error checking for pinctrl was added. Detect them now, and in
their case, simply skip over pinctrl configuration.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.
The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:
i2c_register_driver() i2c_del_adapter()
driver_register() ...
bus_add_driver() ...
... bus_for_each_drv(..., __process_removed_adapter)
... i2c_do_del_adapter()
... list_for_each_entry_safe(..., &driver->clients, ...)
INIT_LIST_HEAD(&driver->clients);
To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().
The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:
% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Internal error: Oops: 17 [#1] SMP ARM
CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
task: e5ada400 task.stack: e4936000
PC is at i2c_do_del_adapter+0x20/0xcc
LR is at __process_removed_adapter+0x14/0x1c
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 35bd004a DAC: 00000051
Process sh (pid: 533, stack limit = 0xe4936210)
Stack: (0xe4937d28 to 0xe4938000)
Backtrace:
[<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
[<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
[<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
[<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
[<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
[<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
[<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
[<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
[<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
[<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
[<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
[<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
[<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
[<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
[<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Some SoC might load the GPIO driver after the I2C driver and
using the I2C bus recovery mechanism via GPIOs. In this case
it is crucial to defer probing if the GPIO request functions
do so, otherwise the I2C driver gets loaded without recovery
mechanisms enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I2C DesignWare may abort transfer with arbitration lost if I2C slave pulls
SDA down quickly after falling edge of SCL. Reason for this is unknown but
after trial and error it was found this can be avoided by enabling non-zero
SDA RX hold time for the receiver.
By the specification SDA RX hold time extends incoming SDA low to high
transition by n * ic_clk cycles but only when SCL is high. However it
seems to help avoid above faulty arbitration lost error.
Bits 23:16 in IC_SDA_HOLD register define the SDA RX hold time for the
receiver. Be conservative and enable 1 ic_clk cycle long hold time in
case boot firmware hasn't set it up.
Reported-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.
However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.
So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus block command uses the first byte of buffer for the data length.
The dma_buffer should be increased by 1 to avoid the overrun issue.
Reported-by: Phil Endecott <phil_gjouf_endecott@chezphil.org>
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.
We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd301. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.
If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Fixes: 4f001fd301 ("i2c: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.
So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXdn2gAAoJEN0jrNd/PrOhe94P/j+1I3iGpHcU/mNmCaqgit9z
TLMehmgglf9kj0iXpYoBjYU/XxzRKBfOaceRrPj16V9GbhiKGcHX0fhH06zydczS
ZPS5FBNGqH9C6WYe8oszTBWz5skulSQba6VUwG01MnT2Nv7z7ONcHB2HPjM6TKob
D0dxN4U3BlfTCGd/FxJariork2xY8o8mKZN7pntkJ+hQNeengCXXoPaY2bGSFH4K
omfUal8/tdPZAruMaA/Dmvu9jBv0RkVSQzNnHXNkGzAw3fAsYm1UzcpG4VNhgeyj
XNFiedIFOls8KW2Xd0LdPAzpyafS4w4gBj2SOol0xpUFhA9CchZCzci7DI2NSj9A
VpiZzBPt6I+zv9c2HdzRqjH2PZTRoy0c9/szCBWyabZ/tST3SWk/tBY5SoLYpmL7
Jq/sOWtegpGvj2XRw8jhmxXVjXYzqzAbyo6SrINZs8ElFrWZxTgsVHmq2SVE5qvh
DnIpr7y/gfKyqAynm0QshNCo5kauvSX4Pa55MfEB/7GfkqhvYzjg+nlplut9woSG
+JN3dWS5tts9pqzHWVL4YY/S11Dx+pT6ZPkmprjMAN+ghxNWjEhA57q7FxAHTU83
BsermHINCpCcN/zyLGDXSaJbJq9hH5LLCHA23ZfnWtOFC5zikp1TG325A/2WMnwb
ovKSLXRScyVqliffmO8G
=+0Q/
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into i2c/for-next
[wsa: fell through the cracks, applied to 4.9 now]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c: 'i2c-bus' node support for v4.8-rc1
This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs
Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
axxia_i2c_probe() does not disable clock in case of failure
in i2c_add_adapter(). Also it ignores returned value from
clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.
Return -ETIMEDOUT in case of a failed data read. For all other
cases just return so subsequent operations will fail.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.
Add wait code to relax the status register check.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
